#ULTIMATE PEN STORAGE RACKS FREE#

Make sure to flatten your wire more than we did here as it is easier now than later! A sharp pair of wire dykes is a must! Also a 'J-clip' tool. Sheila is so patient and supportive! Sheila connecting all the wire as I was cutting it. NOTE: Make sure your bottom 1x2 wire is running in the direction in picture WITH the wires running front to back ON TOP> Otherwise eggs will not roll! Sheila has worked the side wire almost half way around the bottom panel as quick as I could cut her more side wire to clip on! Start anywhere adding the sides to the bottom but pay attention to the corners and the front where egg tray will be formed later. It will have trim installed on all sharp edges when finished. Keep in mind that the egg tray does not need to come all the way to the end and can be stopped at the inside edge of the corner tubing SPECIAL NOTE: Details of the end of the egg tray. THEN TRIM 1' FOR EGG SLOT!!!!! IT MAKES IT A LOT EASIER AS USING THE METHOD SHOWN IN THE PICTURE BELOW ALLOWS THE WIRE TO SLIDE DOWN!!! Front corner showing front and side wire configuration. BEND AROUND THE CORNER AND CONTINUE TO ADD WIRE FOR THE FRONT. SPECIAL NOTE: IT IS BETTER TO START THE WIRE 4' PAST THE CORNER AS SHOWN BELOW. You will leave 1' on the front edge of the bottom to bend upwards later to form the egg tray. STEP 2: Attaching the side to the floor: 1] Once bottom panel is cut and joined, start adding side wire to the bottom panel starting 2' from the edge of the egg tray as shown below.

You can trim wire a square or so when making final joining. We went 11'Дў] Cut the wire from your roll across the edge of the roll to avoid waste.ДЈ] Cut enough to reach all the way around the entire floor keeping in mind to stretch the wire tightly at corners to help keep wire tight. You will want to bend the wire hard against the corner tube General Layout: Side and Front Panel STEP 1: Making the side wire panel: 1] Cut the wire as tall as you want the pen. NOTE: do not attach side wire to the single wire left on outside of the cutout. This is the cutout for the bottom back corner of the pen. You will want to bend the side wire around the corner pipe tightly. Do not attach side wire to the single wire left after making the cutout shown here. NOTE: You can stop wire at the top of the cutout OR fold it over a few spaces for added strength STEP 3: Cut the back corner cutouts: On the back side of the panel, make the cutout shown here. You will bend the short part to form the egg catching tray. SPECIAL NOTE: The wire that runs from front to back of the bottom wire MUST be placed as shown with the wires running front to back on top of the wire running side to side or the eggs will not roll! STEP 2: Cut the front corner cutouts: On front side of the bottom panel make corner cutout shown here. Also note the direction of the bottom wire. This shows the bottom layout and cutouts. SPECIAL NOTE: Also note that the wire that runs front to back should be'on top of' the sideways running wire to allow eggs to travel to collecting trough! Seems almost made with our purpose in mind! General Layout: Bottom panel Our unit will be about 18вЂі shorter! All molded plastic and easy to assemble instructions included. Shelf unit before many alterations to make our DIY quail pen plan using pre-made shelving system. Walmart Shelf System we used: The unit we got for this project from Walmart 1 8вЂІ 1вЂіx2вЂі wood strip for poop tray handles.

#ULTIMATE PEN STORAGE RACKS FREE#

Has sliding вЂњpoopвЂќ trays for easy odor free removal.Instructions include plans for waste-less feeders and automatic water system.There in very little possibility of rotting.We used a ready made shelf system from Walmart. We have seen plans for units made of PVC and the sittings for joining the PVC are pretty high.

It is designed to last a long time and be pretty well self running. Here we give you our take on a complete balcony/porch/garage DIY quail pen plan using pre-made shelving system for breeders, layers and even for brooders. EZ to fix though!ДIY quail pen plan using pre-made shelving system: SPECIAL NOTE: Use 3-6вЂі below floor wire for poop tray removal! We learned the hard way with only 1вЂі. Another way to configure your quail pens.

Ultimate pen storage racks